|
A. Mounting procedures for KTMT-1315, 1700,
1900 and 1921 (with plastic frame):
1.
For
Mounting on LCD monitor:
There are two sets of hangers included; one pair of plastic hangers and one
pair of Velcro hangers.
1.1.
You may use the plastic hangers. Place the touch screen panel on a flat
table with the backside facing up. Screw two hangers into the back of the
panel using the top screw holes on the hanger (picture 1).
1.2.
Adhere two
Velcro straps provided on the top of the display as indicated by the arrows
in picture 2.
1.3. Mount the touch screen to
the display (picture 3).
1.4. If
you find the top of the touch screen is blocking the view area of the
display; you may raise the touch screen by adding the foam pad
underneath the hangers (picture 4).
1.5.
Alternatively, you may use the Velcro hangers (picture 5). The soft surface
of the Velcro faces up when fastening them with the screws to the frame.
Mount the touch screen to the display and press the Velcro firmly (picture
6).
1.6.
You must also apply the Velcro at the bottom of the screen (picture 7) to
secure the mounting. Use the cable clips provided to secure and organize
the touch screen cable (picture 8).
2.
For
mounting on CRT monitor:
2.1.
Measure
the top frame of the monitor (picture 1). If it is 1.5 inches (3.8 cm) or
less, use the top holes on the plastic hangers to screw into the touch
screen panel. Otherwise, use the bottom holes.
2.2.
Place the
touch screen panel on a flat table with the backside facing up. Screw two
hangers into the back of the panel (picture 2).
2.3.
Hang the touch screen onto the monitor in center position. Use a pencil to
mark the hangers’ position on top of the monitor (picture 3).
2.4.
Remove the touch screen from the monitor. Adhere two pieces of Velcro
straps (provided) onto the top of the monitor near the pencil marks (picture
4).
2.5.
Mount the touch screen panel as close to the monitor as possible with the
hangers aligned to the Velcro strips (picture 5).
2.6.
Press down the hangers firmly to fasten the Velcro strips (picture
6).
2.7.
Adhere the Velcro at the bottom center of the screen (picture
7).
2.8.
Adhere the 3 cable clips to the side of the monitor to organize and secure
the cable. This can also prevent the screen from dropping down to the
ground directly if it gets knocked off of the monitor (picture 8).
3.
Continue to Controller &
Driver Installation.
B. Mounting
procedures for KTMT-1700W, 1900W, 2200W and 2400W (with metal frame):
1. This model has a
pair of hangers instead of using vertical Velcro straps. There are 4
ways to assemble the hangers depending on the width of the notebook's top
frame.
|
1.1. Screw through the
top 2 holes of the hangers to the frame. This mounting should be
suitable for most monitors. |
1.2. If the top frame of your
monitor is very wide, you can drop your touch screen by screwing through
the bottom 2 holes of the hangers to the frame |
1.3. If the top frame of your monitor is narrow, you can turn the
hanger over and screw through the top holes of the hanger to the frame. |
1.4. If the top frame of your monitor is extremely narrow, turn
the hanger over and screw through the bottom holes of the hanger to the
frame. |
|
 |
 |
 |
 |
2. Adhere
the Velcro pads to the bottom of the hangers. Remove the wax film from
Velcro. Unbuckle the bottom Velcro straps.
3. Align and hang the touch screen in front of the display .
Press the hangers down to make the Velcro adhere to the top of the display,
and buckle the horizontal straps to the back of the monitor.
4.
Continue to Controller & Driver Installation.
|
