|
KEYTEC
ACEeBoard Quick Setup – see user's manual for more details.
Download PDF of this document
|
ACEeBoard
consists of 2 receivers, connected by a cable. The left receiver
has two cables (one is for the USB cable to the computer and
the other is a cable that connects the left receiver to the right
receiver). Right receiver should have only 1 cable that
connects to the left receiver. Please keep in mind that it will not
work properly if the receivers are positioned incorrectly.
Note:
The receivers should be mounted at least 1” (2.5 cm) above the
projected image area. They may need to be mounted higher when using
on flat panel displays |
|
For
whiteboard or projection screen with thick frame mounted on the
Stand or on the wall - Attach the receivers on the top of the
whiteboard frame
|
 |
|
For
whiteboard or projection screen with a thin frame mounted on the
stand - Assemble the acrylic holders with the receivers as shown
below, place each receivers on the top corners of whiteboard frame. |
 |
|
For
whiteboard or projection screen with thin frame mounted on wall -
Place receiver onto the top of the steel bracket using double-sided
tape. Attach the steel bracket to the back side of the whiteboard. |
 |
|
For mounting
Receivers on the flat surface directly - Place receiver onto the top
of the steel bracket using double-sided tape. Attach the steel
bracket to the wall using screws or double-sided tape. |
 |
|
For mounting
the receivers on flat panel displays - You may use any proper method
to raise and mount the receivers about 5” above the display.
Mounting
fixture is not included, but you may contact us to purchase a simple
fixture as shown. Part number: ACE-AP. |
   |
|
Connect USB
cable from left receiver to a USB port on the computer. If cable is
not long enough, use active USB extension cable. Connect
Projector or flat panel display to the Computer with VGA cable.
|
|
Insert the
CD, click on Install to start software installation. If auto run
does not work, Run POPStarter.exe from CD. It is better to have the
computer connected to the Internet for update information.
After
installation is completed, 2 icons will appear on the desktop: Mint
Control and Mint Interactive. |
   |
|
Double click Mint control to
open the control panel. For the first-time calibration after the
hardware setup, click “initial setup”. For recalibration in the
future, click “screen calibration”. |
|
In the next screen, click
“Next” to continue. You will need to select “Quick setup” or “Fine
setup”. Quick setup is normally recommended. If you experience
difficulty of achieving the accuracy of touch, you may run “Fine
setup”. |
|
|
|
Follow and touch the center
of circles appeared on the screen to complete the calibration
process. Check the accuracy of touch. Recalibrate if necessary. If
“Fine setup” is selected, you will need to touch each X appeared on
the top of the screen to complete calibration process. |
The digital pen works like a
mouse pen.
Pen tip: same as left mouse click.
Lower button: same as right mouse click.
Upper button:
1. In Mint Interactive mode – toggle between writing and eraser
functions.
2. In Windows mode – press and hold will exit Windows mode and back
to Mint Interactive mode. |
Digital Pen: |
|
The digital pen can be
charged from computer's USB port. |
 |
Mint Interactive is an
interactive whiteboard software. Double click the Mint Interactive
icon to run the program. There are two ways to display the tool bars
– Bar type or Floating type.
 Toggle
between Mint Interactive mode and Window mode.
 Pencil,
highlighter, brush.
 Erasers.
 Color,
size, shapes/lines/diagrams.
 
Text input, edit.
 Screen
capture, recording.
 Previous
page, next page.
 Insert
new page, delete selected page.
 Redo,
undo.
 Shift
window, tool & utility.
 Shift &
zoom, setup options. |
Bar type
Floating type |
|
